- Day 4:
- Switch on the radio, great there’s a contest going on, lets try to make some QSOs on 40m.
First try, very strong station but hey, he can’t hear me. Try again a few times.
Suddenly I notice I don’t get any power out…
I restart the radio, I restart the software, I try the other antenna connector, I reset all parameters to default but all to no avail.
Game over already? - Update: I switched off the software to write the small text above. A few minutes later I start the software again and guess what… everything works again! I’m back in the running but I can’t figure out what could have gone wrong. Time to make some more QSOs!
- some conclusions:
- QRP works! 🙂 Also with about 15W you can make QSO’s!
- according to some of the stations I worked this cheap computer headset has a pretty good modulation. Maybe with a little tweaking of the equaliser I can get it even better.
- Switch on the radio, great there’s a contest going on, lets try to make some QSOs on 40m.
Category: SunSDR2pro
ON5MF goes SDR (1)
Due to the lowering in price and the low GBP vs EUR exchange rate I finally decided to offer myself a SunSDR2pro. I know, the SunSDR are not produced in the UK but the price in the UK was about 15% lower than in the rest of the EU.
These are my findings trying to start the transceiver:
- 23+ years in ham radio for now and I feel a complete beginner! This is so completely different from the ‘knobbed’ transceivers I have used in all those years.
- Day 1:
- first things first, installing the software. I downloaded version 1.1.2 from the Expert Electronics site.
- Next came trying to connect the transceiver to the pc. It should be possible to run the transceiver over the LAN/WAN but for simplicity I chose to connect the network cable directly between the transceiver and the pc.
- the user manual says to configure the pc network card so it gets its IP number via DHCP. Well… this does NOT work for me. Of course Google is your best friend and I found this Youtube movie made by ML&S explaining how to set up the pc to the correct fixed IP-address.
After watching this movie I could let the software connect to the transceiver. Finally the spectrum and waterfall screens came to life.
TIP: set your PC to a fixed IP adress in the 192.168.50.*** range.
- the user manual says to configure the pc network card so it gets its IP number via DHCP. Well… this does NOT work for me. Of course Google is your best friend and I found this Youtube movie made by ML&S explaining how to set up the pc to the correct fixed IP-address.
- after some fiddling and attaching a small test wire to the antenna connector I could listen to the different broadcast stations in WFM. You have to start somewhere 🙂
- Now was the time to connect a microphone to the rig… but alas, a complete flea market in the attick but no microphone that can be connected directly. It was getting pretty late at night so I gave up and went to bed.
- Day 2:
- still no microphone in stock so time to try something else: can I get the CAT interface to work with my DXlab logging software? No luck, DXlab’s commander gives ‘COM4 already in use’. So for some reason the SunSDR is blocking some of my COM ports. A quick search on Google and on the SunSDR forum does not yield a solution so I started a new thread on this forum.
I really need Commander to have my remote antenna switch choose the right antenna. Without Commander running all my coax cables are connected to ground.
- still no microphone in stock so time to try something else: can I get the CAT interface to work with my DXlab logging software? No luck, DXlab’s commander gives ‘COM4 already in use’. So for some reason the SunSDR is blocking some of my COM ports. A quick search on Google and on the SunSDR forum does not yield a solution so I started a new thread on this forum.
- Day 3:
- Vassil RN6LHF the developer of the SunSDR has replied to my question. I should use the latest version of the software. And indeed v1.1.3 RC7 solves my COM-port problem.
TIP: always use the latest version of the software!
So time to connect a real antenna to the rig and listen around on HF. - A quick trip to the shop today yielded me a computer headset I could connect to the MIC1 port of the SunSDR.
- New problem found: the jumper cable from mini UHF to PL259 works OK but the adapter plugs I purchased separately can not be tightened correctly on the transceivers connectors. I guess I’ll have to send them back to the supplier.
- After connecting my LDG AT-200ProII it’s time to try a qso and, eureka, I manage to work a belgian station on holiday in EA on 40m.
- To get some decent power out in SSB using the computer headset I had to set the mic gain to maximum and compression pretty high. But that should probably work better once I get the correct interface cable to connect my Heil Pro-Set 4 to the SunSDR.
- The transceiver gets pretty hot even in RX. The internal thermometer indicates 46°C at this moment. According to the user manual this should be ok. I prefer to have my electronics running cooler. So lets see if I can find a suitable ventilator in my junkbox.
- Vassil RN6LHF the developer of the SunSDR has replied to my question. I should use the latest version of the software. And indeed v1.1.3 RC7 solves my COM-port problem.